It is really an amazing experience to fly a drone. However, the drone not taking OFF is a frustrating condition. Drone not taking off problem has many reasons.
For example, it can be caused by low battery charging, improper compass calibration, or software bugs. While the issue may be intricate such as the faulty propellers or the damaged motor.
However, you can fix this issue at home. This guide intends to solve your problem of drones not taking off.
We suggest you follow the guidelines correctly and apply all the troubleshooting tricks.
1. Check the Blades
Sometimes, it happens that the blades of your drone are spinning but it cannot take off. This issue occurs usually after interchanging the blades.
Because all of the drone blades are not identical. Hence, each should be fitted in its suggested location. You might have detached the blades and reattached them wrongly.
So, consult the user manual to look at the correct position of blades relative to the motor.
Further, make sure that all the blades are fitted firmly to the motor. If they are unbalanced, your drone cannot take off.
2. Swap the Blades
The blades might be incorrectly fitted. Give the flying command to your drone and try to lift off it from the ground. Carefully observe which side stays on the ground.
It may be tilted or unbalanced. So, exchange this blade with the opposite one and try again. Be sure to tighten the nuts fully. Otherwise, the propellers will be slipped on the motor shaft.
3. Warm-Up Properly
One reason for the drone not taking off is that it requires a longer warm-up. In this condition, your drone is powered ON and seems ready to fly but cannot.
You can diagnose this issue by observing the LED indicators and communicative messages. Most modern drones have an advanced system that informs the owner about their state.
We recommend you let your drone warm up for a few more seconds. Wait patiently for 3-5 minutes. In cold weather conditions, the drone takes more time to take off.
4. Check the Power
Weak or low batteries is another reason your drone is not taking off. Make sure your drone is powered ON and has enough energy.
Connect it to the power supply and let it charge for 30-60 minutes. A new drone is generally not charged fully. So, you must charge it before the first time usage.
Further, check the power supply. Ensure that your device is receiving adequate voltage. Use the original cable and adapter to charge your drone.
If your drone operates on batteries, try replacing them. Always use the compatible and suggested batteries. Moreover, check the remote controller batteries. Replace them if they are too old.
5. Expired Batteries
If still, your drone is not taking off, its batteries may have expired. They cannot charge properly or empty very fast. So, your drone cannot get enough power to fly.
It generally happens with older drones. The batteries can work for a specific period. Hence, you need to replace them with new ones.
Consult the manufacturer or purchase from a trusted supplier. You also need to check whether the batteries are compatible or not.
6. Incorrect Compass Calibration
Wrong compass calibration can also lead to this issue. It is necessary to check the user manual and follow the guidelines accurately to calibrate the compass.
Specifically, in new and unfamiliar areas, compass calibration is important. Make sure to remove any interference while calibrating your drone.
For example, metal objects, magnets, wristwatches, or jewelry items can interfere with the process.
7. Software Issues
Software glitches can also cause the not taking off the issue with your drone. Although blades spin but the drone cannot take off. It happens with advanced types with more intricate software.
Software issues can be resolved by updating or resetting the drone. Check the remote control settings of your drone.
Check for the latest software update on the mobile app of your specific drone model. Install the latest software version on your drone.
Moreover, update your mobile phone to the latest software version. If this does not work, reset your drone.
The reset method is different for various drone models. However, a general method is as follows;
- First, power ON your drone and wait for all the LED lights to glow solid green.
- After 30 seconds, hold the power button for 30 seconds.
- The two LEDs on the drone should start blinking red. Keep holding the power button until these lights turn solid green.
- Your drone is reset now, try flying it again.
8. Restricted Flight Area
Sometimes, your drone is alight but the flight area is not suitable. Your drone may not be registered properly. The state area where you are trying to fly does not allow drones.
So, confirm that the control app is linked to your account and phone number. The latest drones with more advanced software systems have built-in restrictions.
They can detect the NFZ (No Flying Zones) or geofenced areas. NFZs include military bases, airports, schools, power plants, historical places, gatherings, and others.
So, your drone will not fly in order to abide by FAA drone laws. You can check AirMap to get information about safe flight areas.
This site can help you detect the NFZs as well as danger zones. In this case, you should try to fly your drone in a non-restricted area to check its performance.
9. Defective Hardware
If all else fails, your drone has defective hardware. Either the propellants or the motor has some intricate fault.
The unit can have a manufacturing fault. In this case, you should consult the company.
While the hardware may have damaged due to careless use. For example, your drone may have fallen on the hard ground or hit something.
So, you need to scan the internal system completely. Contact a drone technician to diagnose and fix the issue.
Also Read: Drone Not Pairing Solution
Hopefully, our article will prove its worth for you. We have explained everything in detail. You should apply all the solutions mentioned here.
However, if they cannot fix your drone, contact a professional or the manufacturer. Because this indicates that your drone is internally damaged.
We will appreciate it if you tell us in the comment section which of the tricks fixed your drone that was not taking off.